UNIPOWER Blog

UNIPOWER at ELECTRONICA

2010-09-29T16:29:00.002-04:00

UNIPOWER once again will travel to Munich to participate in the Electronica Exhibition this coming November.

At this show we will be showing our latest power products now in our catalog.

Special focus will placed on our Bluestreak Series of Front-ends available in 12, 24 and 48V outputs.

Plan to visit us there!

Long Run UPS Systems

2010-08-12T16:11:00.003-04:00

Widely available UPS systems are designed for short (<1 hour) discharge or backup. Once extended backup times are required these UPS systems become expensive and are very limited in overall capability. Recharge time also becomes a factor with these systems and this becomes important where the grid is unreliable or unstable.

Scalability is also a factor as most UPS systems are not scalable or have very limited scalability and may become an important issue if system requirements demand more power, more backup time or faster recharge times.

UNIPOWER Long Run UPS Systems are designed using "Telecom Grade" rectifiers (chargers) and inverters and can be configured to meet specific back up times and recharge requirements.

Telecom grade batteries are used with these systems to improve reliability and extended system life.

Contact UNIPOWER for your own Long Run UPS configuration.

USING BLUESTREAK FOR I²C APPLICATIONS

2010-02-09T11:40:00.001-05:00

The communications hardware in BLUEstreak™ meets the requirements of the SMbus standard.
SMbus is essentially an I²C implementation in which certain parameters have been defined to ensure interoperability between different vendors’ products.
Examples are bus timing and voltage level thresholds, which were not so clearly defined in early I²C implementations such as that used in UNIPOWER’s PowerCassette™ Front-Ends. Bus timeouts were also added so as to eliminate the bus ‘hanging’ when the addressed hardware does not respond within a reasonable time.
The SMbus specification also includes a set of defined command protocols; again, to standardise on the way in which the hardware should respond when sent a specific string.

UNIPOWER’s BLUEstreak implements the PMbus. This is a command structure with defined responses that has been developed by the power supply community along with a number of users as a kind of ‘superset’ that will yield ‘known’ results when implemented fully.
PMbus uses a specific set of SMbus commands that has been defined for use in power supplies, in particular for distributed power applications. It's sort of a superset of commands.
At the lowest level I²C hardware is interrogated by directly addressing a register and reading back its content; but there is no predefined structure to this data, so it then has to be interpreted in software to create a meaningful result.
The SMbus structures they way in which the hardware is interrogated in the form of a series of standardized command types (protocols).
For more information about SMbus we recommend that the reader obtains the “System Management Bus Specification” which is available in PDF format from www.smbus.org/specs/smbus110.pdf. In particular we draw attention to pages 21-26, where the command protocol is detailed, and to pages 37 and 38, which describe the main differences between basic I²C and SMbus.

With PMbus a set of commands specific to power supplies has been defined along with formatting of the returned data string.
With the exception of a small number of manufacturer specific commands PMbus need only be coded for once, regardless of which hardware is involved.
For more information about PMbus we recommend the reader obtains the current published PMbus specification revision 1.1 (as utilised in BLUEstreak) from www.pmbus.org/specs.html. In particular, page 21 section 7.1 shows the command format for common output readings such as voltage and current while page 75 shows the structure of two typical status bytes.

In summary:
I²C = 2 wires, clock data, address + data
SMbus = 2 wires, clock data, address + command code + low data byte + high data byte + timeouts
PMbus = SMbus + PSU commands with defined data structure.

Customers who are familiar with basic I²C as well as the SMbus command protocols can communicate with BLUEstreak provided they are using SMbus compliant hardware and can implement SMbus commands in their management system, for example in an aTCA implementation.
This will allow them to obtain readings of voltage, current, temperature and fan speed (as examples) as well as obtaining inventory information from the on-board EEPROM.
They can also send commands to the power supply to change parameters and control its operation.
It should be noted that a basic I²C management system may be able to communicate with the BLUEstreak. This is the case with UNIPOWER’s own DSC1000 power system controller. UNIPOWER cannot make any guarantees that non-SMbus compliant management systems will work.

Integrating Power Systems

2010-01-05T15:46:00.003-05:00

UNIPOWER now integrates small to mid size power systems to customer specifications.

UNIPOWER has added the internal capability and has the accessories, batteries and many other components in stock to integrate customer specific power systems that can be put together using many of UNIPOWER's standard power components.

These power components can be integrated by mounting them on a relay rack and wiring the different sub systems together to achieve a desired customer specification.

UNIPOWER has the unique ability to supply not only 48VDC systems, but also 24 and 12VDC systems; using standard systems components.

Components available for integration are:

RECTIFIER SHELVES AND RECTIFIERS

SYSTEM CONTROLLER

DC DISTRIBUTION (BREAKER/FUSE PANELS)

RELAY RACKS, 19" OR 23", 50" or 7 feet high

BATTERY TRAYS

BATTERIES

BATTERY BREAKERS

...and many other pieces to the system's puzzle.

These systems are shipped pre-wired and tested at the factory for simple and trouble-free installation by our customers. These systems are also individually documented as a single, distinct model number for future orders and for any necessary customer support.

Please contact us for with your NEXT system requirement!!!

NorthStar Batteries now in stock

2010-01-05T10:13:00.005-05:00

UNIPOWER now with batteries in stock to serve our customers' total systems needs with instant delivery...

A common theme with our customers is the lack of availability of batteries for their systems requirements. To address this issue, we have worked together with NorthStar Batteries to make available to our customers a significant inventory of the most commonly used batteries.

The models to be maintained in stock are as follows:

NSB 60FT

NSB 100FT

NSB 170FT

UNIPOWER will monitor and maintain inventory of these battery models in our Coral Springs, Florida facility for immediate shipment to our North American and Latin American customers.

Other models may be added later, if necessary for support of our customers.

We thank NorthStar for their assistance in this process.

Virtual Trade Show

2009-12-14T14:49:00.004-05:00

On Wednesday, December 9th, UNIPOWER participated in a "virtual trade show" hosted by Globalspec. This show had our booth showing many of our products, it also had literature that was available for downloads by our visitors. Our booth was staffed by seven team members representing sales and engineering from North America and Europe.

At this Show, we featured Inverters, DC/DC Converters, Multi-output power supplies, and front ends and rectifiers. We ran a short video of our Telecom booth, were we highlighted our entire Telecom product line.

The show began at 11:00 AM EST and ended at 7:00 PM EST. During these 8 hours we were visited by over 220 interested parties, including some of our Sales representatives in the US as well as some of our international distributors. We were able to "chat" with each visitor and were able to offer answers and assistance on our products.

Like any show, meeting new potential customers is what is all about and we certainly got to do this.

The job of following up with our many visitors is underway and we look forward to our next "virtual trade show"...perhaps some day all shows will be like this!

Australian Partners visit UNIPOWER Europe

2009-10-13T12:54:00.007-04:00

On 12th and 13th October the staff at UNIPOWER's European office welcomed four members of the team from our agent in Australia for a two days of product training.

Delia Jones, Ian Hansen, Malcolm Scott and Bryan Cook took a detailed look at UNIPOWER's comprehensive range of power conversion product as well as delving into the depths of the software features that many of these now offer.

"Our time at Unipower was friendly and relaxing; but above all a very informative time. Being able to meet with the guys on a face to face basis we learned a great deal," said Dewar General Manager Ian.
"The product knowledge we gained could not have been achieved without visiting UNIPOWER and we feel we are now in a great position to ensure our customers in Australia and New Zealand make the right choice when selecting a vendor for their power requirements.
There was one moment of tension however when we were challenged to a table tennis match. We did manage to hold our own against some stiff competition and didn't let go of those particular ashes!"

Supercomm 2009

2009-10-05T12:27:00.003-04:00

UNIPOWER will again participate in Supercomm this October in Chicago.

This will be the 9th time that UNIPOWER will be an exhibitor at this important show. The company will again return with an updated and refreshed 10 x 20 booth, that can be found in location 5025.

This year the company will present new products that represent the company's new focus on providing standard integrated power systems and also its ability to configure and integrate many of it's standard power components into "one of a kind" solutions for customers looking for fast and easy to install power solutions.

Highlighted at Supercomm will be UNIPOWER's new Bluestreak Rectifiers, a series of high-density, high-efficiency modules that boast 92% efficiency. These rectifiers will be also found incorporated in the new Gravitas X200 Compact System as well as in its Gravitas X450/X650 Power Cabinets.

Along with these systems the company will show examples of its pre-configured AC backup systems that include battery chargers, inverters, transfer switch, comms module and even various distribution possibilities. These systems ship all in a single box and once easily connected can be up and running in a matter of minutes.

We look forward to seeing our customers and friends at Supercomm, Booth 5025.

Battery Protection in Telecomn Systems

2009-05-15T13:18:00.002-04:00

Battery Protection in Telecom -48V Rectifier Systems

In telecom power systems using battery backup, the battery size in Ampere-Hours(AH ) is determined by the maximum system load in amperes and the backup time in hours to maintain the system output voltage within acceptable limits during an AC power failure.
Generally, for battery backup requirements exceeding 1.0 hours, multiple battery strings are required. These strings are connected in parallel across the 48V bus and each string should carry it’s equal share of the total system charge and discharge current. During the discharge time the battery supplies the total system load. Each battery string must be rated to supply a current equal to the maximum total system load divided by the number of battery strings. It is good practice to use circuit breaker protection in each string to provide overload protection, and this is also useful in providing a method for manual disconnect for each individual string for maintenance and service. It is recommended to rate the circuit breaker current at a minimum of 25% above the maximum string current as defined above.

During the charge time, after AC power is restored, the battery will be recharged at a current equal to the total rated rectifier current capacity minus the total system load. It is important here to ensure that there is sufficient rectifier capacity beyond the system load to meet the recharge time requirements. In most systems the recharge time requirements are typically substantially longer than the discharge time requirements at maximum system load, and as a result, the battery current during recharge will be lower than the battery current during discharge. Therefore, circuit breaker protection defined for the discharge protection should be satisfactory for the recharge protection.

Custom Powersupplies

2009-04-22T11:28:00.006-04:00

EASYMOD switchers are 40W to 350W single and muiltiple output units which are available with Industrial and Medical approvals with both AC and DC inputs.

EASYMOD simply means, "IF WHAT YOU SEE IS NOT WHAT YOU WANT, IT CAN BE EASILY CHANGED".

The philosophy of the EASYMOD product family is one where the design is flexible and allows for key features such as output voltages and current ratings to be tailored to meet your specific requirements WITHOUT the need to re-submit for agency approvals; and we can do all of this for programs requiring as few as 250 units per annum.

EASYMODs include: extended temperature operating range (INDUSTRYMOD), isolated outputs, unique output combinations, DC input, low noise versions and much more.

Next time you ar looking for a 40W to 350W switcher that does exactly what you want it to do give us a call.

High Efficiency Powersupplies

2009-04-21T13:49:00.001-04:00

UNIPOWER Corporation announces its latest generation of high-density, hot swappable 48VDC modular rectifiers and front-ends. Called BLUEstreak™, the series combines high power density with high efficiency levels. The Front–end version will be factory set at 48VDC while the Rectifier version will be set at 54.4VDC.

BLUEstreak units can provide up to 2000W from a 1U high package at power densities as high as 23.4W/in³. Input voltage range is between 85 to 264VAC . Efficiency levels to 92% at 75% load. Four units with a total output of up to 8000W can be housed in a highly flexible 1U system rack.

The modules feature automatic load sharing and output Oring diodes and have an operating temperature range of –20 to +70ºC managed by variable speed cooling fans. LEDs indicate AC and DC power good and two standby outputs are available, +5V @ 1.8A and +12V @ .8A.

Like other UNIPOWER rectifiers, BLUEstreak modules use the I²C based PMBus to pass status and control data between a host system, management unit, and the module.

BLUEstreak rectifiers and front-ends will find wide application in network equipment and data storage as well as in telecom battery systems and will be available from end of Q2. The Series will include additional output voltages and various power levels in the near future.

How to evaluate the benefits of higher power supply efficiency.

2009-03-30T09:11:00.004-04:00

In a push to improve the use of our resources, there are a number of industry and governmental initiatives with the goal of providing products and services in environmentally friendly ways. One of the techniques in the electronics and computer industry that can show almost immediate benefit is to improve the electrical efficiency of the power system. Every electronic system has to have a source of electrical power. Typically the power is derived from the AC mains or from banks of batteries. In almost every case, there is a need for an electronic converter that will take in this raw electrical power and convert it to a well-regulated, low voltage DC level that can be used to power the electronics. The efficiency of this electrical conversion process is defined as the ratio of the output power to the input power. The output power is measured in watts, and can be calculated as the product of output voltage times output current in Amps. The input power is also measured in watts, and is also the product of input voltage times input current. If the input is provided from an AC (50 or 60 Hz) mains, the modern power converter will include a processor that will correct the input current so as to be a sine wave, in phase with the input voltage wave. This process is called power factor correction, and ideally provides a sine wave of current that is 99% pure sine wave.

To understand the impact of efficiency, it is useful to look at an example. Figure 1 below shows a chart that gives the input power(Pin) and the output power (Pout) at different output current (Iout) levels for a high efficiency power converter. The efficiency is calculated by dividing output power by input power and listing the result as a percentage. We can also compute the internal power by subtracting the output power from the input power. This is the power that gets dissipated inside the power converter, and is undesirable. This power is wasted in the power converter. It heats up the converter and serves no useful function. Ideally this number would be as low as possible.

There are several interesting features shown on the chart. If we make a graph of internal power versus the load current, it will look like Figure 2. It shows that even with no output current, there is some internal loss inside the power converter. This is generally the power needed to run the cooling fans and provide power for the internal circuits in the converter. Then, as the load is increased there is a gradual increase in the internal loss until we reach, in this case, a level of about 10 amps, and then the internal loss goes up on a steeper curve. This effect is due to the resistive losses in the input and output sections of the converter, and they come to dominate the internal losses as the load increases. The two conclusions that may be drawn from this data is, first, there is a loss at even no-load, which is encountered when the electronics goes into a ‘sleep’ or ‘hibernate’ mode. If even less dissipation is required in this mode, it is possible to inhibit the power supply and turn off the fans and selected circuitry. Secondly, at lower load levels, there is a load range where the internal loss does not increase very much. If indeed the expected loads will be only at low levels, the electronic systems designer should consider re-sizing the power supply or evaluating what the best trade-off would be in terms of providing redundancy in the power systems. There is an ‘overhead’ energy cost associated with redundancy and this should be balanced against the added system reliability advantage that comes with power redundancy.

The chart presented in Figure 1 is taken from measured data on a new, high-efficiency, AC/DC power supply that is optimized for higher efficiency. To understand the cost benefit of this higher efficiency, refer to Figure 3. In this chart, we compare the difference in internal power between the high efficiency converter and a standard one with an efficiency of 80%. The difference between these two converters is shown as the line on the chart with a diamond-shape marker. It represents how much more power is wasted in the less efficient converter at different levels of output loading.

As an example, at a output loading of 30 amps, which corresponds to an output power level of 1632 watts at 54.4volts, there is approximately 268 additional watts of power dissipated in the less efficient converter. If this is powering a constantly on, 24 x 7 piece of equipment, what would be the cost of this wasted power? Electrical energy is costed in terms of a certain cost per Kilowatt-hour. Although cost per Kilowatt-hour vary around the world, let’s take a look at annual cost using a typical cost of $0.10/KW-hr.. In one year there will be a total of 268watts x 24 hr/day x 365 day/year x 1Kwatt/1000 watt = 2348 Kw-hrs/year of wasted power. Cost of this wasted power is 2348 x $0.10 = $234.80 per system per year.

Many users will find that the high efficiency power supply is a good choice, especially when powering critical electronic and computer applications. Although the original equipment manufacturer generally does not incur the operating costs associated with these types of applications, it is a useful feature that will make the efficient system attractive to the OEM’s customers. In addition to the reduced operating costs, the less electrical power that is wasted will show up in reduced cooling requirements for the end customer. Many datacenters, computer/server farms, and Telco equipment are loaded with electronic gear and the cost to cool the hardware is one additional operating cost that goes down when the power conversion efficiency goes up.

This blog was written by Vance Burns, Director of Product Development for UNIPOWER.

UNIPOWER at Electronica Show

2009-03-24T10:17:00.007-04:00

In November of 2008 UNIPOWER once again participated at Electronica Fair in Munich, Germany. This Fair or Show comes together every other year and it is an important part of our European marketing effort. This Fair had 2800 exhibitors with an entire hall dedicated strictly to power supplies. The Show also brought 73,000 visitors from all over the world, with attendance from Easter Europe, South Africa and Latin America increasing this year.

For UNIPOWER it is all about making new contacts and spending time with friends and customers. This Electronica Fair, as some of you may know, is not like American shows, here you actually spend time sharing a beer or coffee with visitors while discussing product features or business points. This year we had a good number of visitors, mostly from Europe, though we also made contact with visitors from the Middle East, Asia, North America and Latin America.

We look forward to the next Electronica Fair in 2010, in beautiful Munich, Germany!

Supercomm Show 2009

2009-03-19T14:40:00.009-04:00

Once again UNIPOWER will participate in Supercomm 2009 with its twenty foot display. The show, originally scheduled for June, has now moved to October 21 thru the 23rd, still in Chicago.

The company has been participating in Supercomm now for 10 years and we believe it is an important event for the company. First and most important is that it allows us to meet face to face with many of our customers. Another important reason for UNIPOWER to participate is to introduce new products and capabilities to the market at large. Every year we have something new to talk about and Supercomm is a great place to show our customers what new products we can offer them to make them to solv etheir problems or to make them more efficient or competitive in their markets. It is also a great place to get feedback on products and ideas for new generation products.

The show has changed over the years, with attendance fluctuating wildly from year to year. For us it is about meeting friends and customers and showing off our capabilities. We hope this year it ends up being a good show, as it would mean that it is a good year for our industry and that the economy has bounced back.

This year we plan on introducing a new generation rectifier system, featuring high efficiency and digital controls in an extremely dense package. More information on this product to come in the next few weeks.

See you at Supercomm in October!

High Altitude Power

2009-03-19T11:32:00.005-04:00

Installations in hostile and high altitude environments are common in the telecommunications business. Sites are located in the most remote places and these require rugged power equipment that can survive the environment.

We thought it would be of interest to show a few photographs of some high altitude installations in South America using our equipment . These installations shown in these photographs are all well above the clouds as can be seen in these pictures and while they are very basic in nature, they still require very rugged equipment from UNIPOWER .

Soon we will be posting on High Altitude operation and derating.

"CHAT" FOR BETTER CUSTOMER COMMUNICATIONS

2009-03-18T09:35:00.008-04:00

UNIPOWER uses "Chat" capability on its website to make communications with customers more efficient. By simply clicking on the "Chat Button" on any page on http://www.unipowercorp.com/ or on http://www.unipowertelecom.com/ , a customer can be in touch with one of our sales or technical support personnel and carry on a fluid, extended dialog.

Customers all over the world use Chat to contact us, as we are able to respond in several languages and provide coverage for 13-15 hours per day.

The ability to communicate in writing in a fast and fluid manner is the key to the success of this system. It is a great substitute for e-mail as there is instant response from the company. It is also a great alternative to voice or phone as it is free to the customer and again, there is instant response from the company.

Custom DC Distribution Panels

2009-03-13T15:34:00.009-04:00

These are photos of one of the many Custom DC Distribution Panels, in this case Breaker Panels, that are produced by UNIPOWER. Even though we make available to customers a broad line of DC Distribution Panels, customers come in and ask for us to design a panel to fit their specific application.

UNIPOWER makes this Custom Design service for DC Distribution Panels available for applications requiring something special and unique that can not be satisfied by one of our many flexible and configurable distribution panels. Before embarking on a design project, we need to know the exact specifications of the customer and we need to know that a minimum quantity of these panels will be bought by the customer.

Typical design cycles for DC Distibution Panels range from 6-8 weeks to four months, depending on the complexity of the product desired. The photos above represent a very flexible panel with high current capacity and pluggable breakers, housed in a longer-than-usual enclosure where the length was dictated by the customer's system access.

Customized Power Solutions

2009-03-12T11:28:00.006-04:00

One of the services frequently provided to our customers is what we like to call "Higher Level Integration" of the our powersupplies. Customers come to us so that we can solve their entire power problems, not just for us to sell them a powersupply and this can be best done by providing a customized assembly that includes the powersupply in it.

The benefit to the customer is that at the last minute in his assembly process, he gets to pick and install a complete "power assembly" the way he would have done it himself. These customized power solutions may include a custom metal enclosure or a special harness or perhaps two power supplies tied together in some way or even a combination of the above mentioned elements of a complete power assembly.

Most power supply manufacturers are not inclined to provide thes services. UNIPOWER is geared to provide these completed, integrated assemblies to customers with expected volumes in the 100s per year and not 1000s per year, where perhaps one of our standard powersupply platforms combined with some extra sheetmetal and wires, etc, can provide a real turn-key solution.

We have included a photo of one application so that the reader of this post can get a flavor for what can be done.

Rack Mount DC/DC Converters Requirements

2009-03-09T09:45:00.008-04:00

When one thinks of DC/DC converters, the first thing that comes to mind is the "brick converters" popular in many applications for Distributed Power Architectures in systems. However, there is a different kind of DC/DC converter that is essential in larger systems that have been designed to operate on one given DC voltage and then find themselves installed in systems where that voltage is not available and therefore needs to be converted. These DC to DC converters are the subject of this post.

UNIPOWER carries a full line of dc to dc converters designed for this very purpose with popular models being those converting 48VDC to 12VDC and 24VDC to 48VDC. these are all rack mount, taking only 1U of rack space in a systems. The racks or shelves are all capable of accepting up to 3 dc converter modules ranging in power from 700 watts each to 1000 watts each, meaning that a single 1U space can provide as much as 3000 watts of dc to dc conversion.

The models available are:

48VDC input with 12VDC output at 650W per module

48VDC input with 24VDC output at 700W per module

24VDC input with 48VDC output at 1000W per module

These systems are all Hot-swap and redundant for use in high reliability DC/DC applications. Multiple racks or shelves can be also paralleled to provide higher power levels of conversion. These converters can work with a fairly wide input range and can also work in battery backed up systems.

Multi-output Power Supplies

2009-03-05T10:31:00.010-05:00

Systems requiring multi-output power supplies represent a challenge to designers. The main reason being that while voltages required are usually known early in the design, power levels or current levels for each of these voltages are not known until late in system design. This pushes out the specification of the power supply until the very end of the process and it ends up being a problem for product designers and product managers trying to get final prototypes of their systems to test and debug.

Over the years, power supply companies have made available to the market many different versions of configurable or modular power supplies in order to achieve fast time to market for OEMs struggling with this problem. UNIPOWER is no different having had success selling several different models to a wide variety of applications over the past 20 years.

Our company's latest entry, the QUIQPlus Series, incorporates many advances and improvements over previous models. Some of these are:

1U high

600W, 800W and 1000W versions

Voltages from 3 to 56VDC

Up to 8 outputs possible

Wide Input from 85 to 264VAC

Completely modular construction

Using the configurator available on our website, customers can configure the multi-output power supply to their own requirement, come up with a unique Model Number and with just a phone call or an e-mail an order can be placed for immediate delivery.

The factory keeps main frames and output modules in stock at all times in anticipation of customers' rush demand. This has proven to be a great product for OEMs and for the company as it can satisfy the endless possible configurations of multi-output power supplies that are required instantly by customers.

The website http://www.unipowercorp.com/ includes an animation of how easily the product goes together, by simply inserting pre-tested output modules into a pre-tested mainframe as requested by the customers, closing the case, automated final test, label and off it goes to the customers...all in a matter of minutes.

Understanding Inverter Output Power Ratings

2009-02-23T08:35:00.011-05:00

Inverter output ratings are traditionally defined in terms of Apparent Power in VA (Volt Amps) & Power Factor. Apparent Power is the product of the maximum output volts & amps available under the most favourable operating conditions for the inverter. This maximum operating point is defined by the Power Factor; the Real Power available in watts is the maximum VA multiplied by this said Power Factor. Real power is the effective power value as if the V & A were in phase & the PF =1 as would be the case if the load was an electric fire bar or a fully power factor corrected power supply.

Probably one of the most basic definitions of power factor is that it equals the cosine of the phase angle between the voltage & current. This is difficult to conceptualize in terms of the input to a non PF corrected power supply because besides the current phase leading the voltage its whole waveshape changes from a sine wave to a series of current peaks. Both effects are due to the large storage capacitance following the input rectifier. This greatly complicates the issue but plays a large part in the reason for the traditional rating method for an inverter.

In many older non corrected power supplies the power factor may be considerably less than 1, say down to 0.6. Even today there are many smaller power computer/server power supplies which only have passive PF correction giving power factors in the region of 0.8-0.9.

It is very important to ensure the inverter is sufficiently rated to drive the load. Consider an inverter having a VA rating of 1000 & power factor of 0.8 giving a real power limit of 800W. Neither the VA rating nor the real power watts rating can be exceeded. If the load PF is greater than 0.8 then the power limits remain as previously defined, however, if the load PF is less than 0.8 the real power limit will be further reduced.

For information on the full line of UNIPOWER Sinewave Inverters go to: http://www.unipowercorp.com/Unipower_Telecom/Telecom_Product_Line/Telecom_Inverters/telecom_inverters.html

HASS Screening For Power Supplies

2009-02-19T14:13:00.001-05:00

Here at UNIPOWER we use HASS or "Highly Accelerated Stress Screening" during the production process to improve the quality of our products. The purpose of HASS is to shake out manufacturing and component defects before shipment to our customers. It is an important element of our Quality Process and an integral part of the production process.

UNIPOWER has been using HASS successfully for over 17 years and has developed a significant amount of expertise in determining the best screening profiles specific to high-density power supplies and systems.

The HASS Profiles designed and used by the company include low temperature, or -15 degrees Centigrade turn on and power cycling, rapid temperature rise while under power to +55 degrees Centigrade, high temperature turn on and power cycling, and two 7 minute vibration cycles at different temperatures. The most used profile runs 30 minutes.

The ultimate goal is to find out problems long before our customers find them and HASS is a much better screen than the typical 4, 8, 12 or 24 hour burn-in process used by most power supply manufacturers today.

DC Distribution Panels Shipped in 24 hours

2009-02-17T13:48:00.000-05:00

UNIPOWER has developed a program that allows customer configured DC breaker panels and DC fuse panels to ship within 24 hours.

For a period of now six consecutive months, UNIPOWER has consistently been able to take orders, configure and ship in less than one day. This flexibility represents and tremendous advantage to customers getting ready for an installation.

Essentially integrators or customers in the field can quickly view the options and possible configurations available from UNIPOWER on the website, call in an order, and feel comfortable about the fact that the shipment will be out the same day or the day after.

More information at : http://www.unipowercorp.com/Unipower_Telecom/Telecom_Product_Line/Distribution_Panels/distribution_panels.html

12VDC Custom Power Solution

2009-02-09T14:26:00.000-05:00

UNIPOWER Corporation has successfully developed a modification of it's TPCM Series product which can now supply 780 watts of power at 12 VDC, increasing power density by 20%.

At the request of a strategic customer, UNIPOWER Corporation successfully developed a customized power solution effectively allowing the customer's next generation product to utilize the existing mechanicals and power configuration. This achievement anchors UNIPOWER’s capacity to provide custom power solutions in addition to a broad standard product offering.

Low Power Switchers

2009-01-29T13:22:00.001-05:00

UNIPOWER announces that it has added a wide selection of Low Power Switchers which are complementary to the existing product portfolio and allows us the opportunity to provide solutions at the low to medium end of the power spectrum.
"We are best known as the hot-swap, high power density specialists and these AC and DC input Low Power Switchers or power supplies , particularly those from 40 to 350W, are welcome additions to our range" adds Nigel Frey, Director of Sales for UNIPOWER Europe.

UNIPOWER has manufacturing sites located in the Far East and the United States and all products are fully approved to relevant international safety standards including UL60601-1 and EN60601-1 for Medical Equipment. As well as a very wide selection of standard products. UNIPOWER can also offer users a semi-custom facility across many of its product ranges.

400 Amp DC Power System

2009-01-26T11:20:00.001-05:00

UNIPOWER Corporation announces a new modular DC power system designed specifically to meet the exacting requirements of telecom systems applications where reliability, flexibility and battery back up are key factors.

The Gravitas X410R DC power system is built around a compact 600 x 600 x 2134mm or 2’ x 2’ x 7’ (48U) freestanding enclosure incorporating 8 positions for hot-swap rectifiers, AC input distribution/protection, DC load distribution/protection, low voltage battery disconnect, battery distribution/protection, system controller, and two or three shelves of front-connect batteries rated up to 185AH each. A vertical space of 12U rack height has been allocated below the power components for optional equipment such as inverters or DC/DC converter shelves and their distribution/protection panels, customer supplied equipment or for an available third battery tray.

According to UNIPOWER’s European Marketing Director, Nigel Frey, the new DC power system supports 48VDC loads up to 400A (21.7kW) and can accommodate a variety of AC inputs from either single or three-phase sources. http://www.unipower-corp.com/Unipower_Telecom/Telecom_Product_Line/Mid-Size/mid-size.html